SSD SUPPORT SOLUTIONS This document contains information that was exported directly from Konica Minolta's SSDSupport knowledge base. Some soluti
Di520TAUS0633826EN00Solution ID0 Solution UsageDescriptionGray/fuzzy background on copies.SolutionPROBABLE CAUSES:1. PM is due. Consider replacing sta
Di520* Trademark ownership information TAUS0634256EN00Solution ID0 Solution UsageDescriptionPart number of the clutch in the punch unit of the FN-3.So
Di520SolutionCAUSE: This is normal operation.SOLUTION: The controller should be booted after the copier is turned on. If the controller locks up afte
Di520TAUS0635862EN00Solution ID0 Solution UsageDescriptionWhen entering Users Choice, only four screens are displayed instead of six.SolutionCAUSE: W
Di520SolutionCAUSE: Even a small amount of developer in stuck to the underside of the developer unit will cause the developer to purge. SOLUTION: Chec
Di520TAUS0639061EN00Solution ID0 Solution UsageDescriptionC099C at power up.SolutionCAUSE: A damaged ribbon cable for Tray 3.SOLUTION: Replace PWB-H
Di520On the Di520 what is the part number for the main wire harness to fuser assembly. This is the main harness at the back of the copier that the fu
Di520TAUS0644709EN00Solution ID0 Solution UsageDescriptionPaper is jamming in the FN3 after selecting folding. Metric paper indication is also display
Di520Upon install, the machine is displaying in Japanese and needs to be converted to English. The flash rom cards have been tried unsuccessfully.Solu
Di520SolutionBulletin 2558 contains information regarding changes to the Di620 Service Manual. The Service Manual illustrates the scanner position
Di520TAUS0629872EN00Solution ID1 Solution UsageDescriptionWhat controller type setting is required for installation of a Pi6200 or Pi6000?SolutionIt n
Di520* Trademark ownership information TAUS0645692EN00Solution ID0 Solution UsageDescriptionStaples and staple cartridge part numbers.SolutionThe foll
Di520Marketing Bulletin #98-06 . Note:1. This bulletin was written about the Di620/Di520, but also applies to the Di450, Di470, and Di550.2. To view t
Di520SolutionCAUSE: Early version firmware installed.SOLUTION: Update the main body to current firmware. Refer to Service Bulletin 2617D TAUS0646
Di520SOLUTION: Replace the Harness (p/n 1155-6815-02).TAUS0649947EN00Solution ID0 Solution UsageDescriptionWhen print jobs are sent from the controll
Di520 Why does pagination change when printing any document using the Konica Minolta print driver? Solution Pagination differences between different m
Di520 7040/IP-411 7045/IP-431 7050/IP-201 7050/IP-301 7050/IP-302 7055/IP-303 7055/IP-304 7060/IP-302 7060/IP-304 7065/IP-
Di520 Minolta Di3510f PCL5e Minolta Di470 PCL5e Minolta Di552 PCL5e Minolta Pi1802/1502e PCL5e Minolta Pi3500 Min
Di520SolutionIts part number is listed in the Parts Manual, figure 37 (Electrical Components II), index 21. The part number is 1155-6815-02.Note:
Di520SolutionCheck that the copier enters pre-drive.Check that the rear cover engages the rear photo sensor.Also, check that the magnet attached to th
Di520TAUS0631792EN00Solution ID0 Solution UsageDescriptionC1330 error codes occur when making two-sided copies 4 into 1.SolutionCause: The firmware ha
Di5201. Failure of upper fuser lamp. Replace the upper fuser lamp.2. Failure of thermistor. Replace the thermistor.3. Failure of thermal fuse. Replace
Di520SolutionThis problem is generally caused by contamination on the width glass. We recommend installing a new glass, part number 1155-1602-03. The
Di520TAUS0632076EN00Solution ID0 Solution UsageDescriptionThe PWB-B is too small to fit on the mounting points in the copier. In addition, some of th
Di520SolutionCAUSE: PWB-B problem(s). SOLUTION: Please check the following:1. All connectors to PWB-B.2. Verify firmware is correct. Refer to bu
Kommentare zu diesen Handbüchern